tps adjustment - Mitsubishi Evolution Forums: Mitsubishi Lancer Forum
Mitsubishi Evo Forum Mitsubishi Evo Forum Header Right
 

» Auto Insurance
» Featured Product
Wheel & Tire Center

Go Back   Mitsubishi Evolution Forums: Mitsubishi Lancer Forum > Lancer Evolution Tech Forums > Tuning & Engine Management
Register Forum Active Topics (T) Gallery Auto Loans Classifieds Garage Mark Forums Read Auto EscrowInsurance Advertise

Tuning & Engine Management Engine Management, EGT temps, timing, wideband, datalogging, fuel trims, etc.

EvoTuners.net is the premier Mitsubishi Evolution Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools
Old 08-24-2005, 03:47 PM   #1 (permalink)
 
Registered: Jul 2005
Posts: 3
Reputation: kevinb is an unknown
tps adjustment

I figured that I would ask around before I wasted time. I'm getting 98% tps at wot. Does anyone know how to adjust the tps to make it 100%
Offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-24-2005, 11:02 PM   #2 (permalink)
EVOtuners Member
 
turbolarry's Avatar
 
Club Region: SoCal
Registered: Oct 2004
Posts: 1,577
Images: 10
Reputation: turbolarry is known to be trustworthy and helpfulturbolarry is known to be trustworthy and helpfulturbolarry is known to be trustworthy and helpful
A volt/ohm meter is needed and the throttle body assembly out;

THROTTLE POSITION SENSOR (TPS) INSTALLATION
1. Place the TPS in the throttle body in the position shown in
(1) of the drawing.
2. Turn the TPS to the position shown in (2) of the drawing.
Connect a circuit tester between terminal 2 (TPS output)
and terminal 4 (earth) of the TPS to measure the output
voltage. Turn the TPS to a position where the output voltage
is within the standard value range, and secure the TPS there
by tightening the screw.
Standard value 0.535 − 0.735 V
3. After tightening the screw, check the output voltage again. If
the voltage is out of the standard value range, loosen the
screw and adjust the TPS position for a proper output
voltage, then tighten the screw. If necessary, repeat the
adjustment until a correct voltage is reached.
4. Connect a circuit tester between terminal 1 (TPS power
supply) and terminal 2 (TPS output). Check that the
resistance reading varies smoothly as the throttle valve is
moved slowly to the wide open position.



Attached Images
 
Offline   Reply With Quote
Old 08-25-2005, 12:12 AM   #3 (permalink)
 
Registered: Jul 2005
Posts: 3
Reputation: kevinb is an unknown
Thanks a lot.
Offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Powered by vBadvanced CMPS v3.2.2

All times are GMT -8. The time now is 07:37 PM.


vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
© 2007 AutoForums.com - EVOtuners.net - All Rights Reserved.

Powered by vBulletin®. Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.3.2
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.